Hot Models
Model | |||||
Channels | 2 | 2 | 2 | 2 | 2 |
Bandwidth | 100MHz | 100MHz | 100MHz | 100MHz | 150MHz |
Sample-rate | 1GSa/s | 1GSa/s | 1GSa/s | 1GSa/s | 1GSa/s |
Memory Length | 2Mpts | 40Kpts | 10Mpts | 2Mpts | 2Mpts |
Auto Measurment | 32 | 32 | 20 | 32 | 32 |
Vertical Sensitivity | 2mv-10v/div | 2mv-10v/div | 2mv-10v/div | 2mv-5v/div | 2mv-10v/div |
Horizontal Range | 2.5ns-50s/div | 2.5ns-50s/div | 2ns-100s/div | 4ns-40s/div | 2.5ns-50s/div |
Trigger types | Edge, Pulse, Video, Slope, Alternative | Edge, Pulse, Video, Slope, Alternative | Edge, Pulse, Video, Slope, Alternative | Edge, Video, Pulse, Slope, Over time, Alternative | Edge, Pulse, Video, Slope, Alternative |
Display | 7 inch | 7 inch | 8 inch | 7 inch | 7 inch |
PictBridge Print | √ | - - - - | √ | - - - - | - - - - |
USB Interface | √ | √ | √ | √ | √ |
VGA Interface | - - - - | - - - - | √(optional) | √(optional) | - - - - |
LAN Interface | - - - - | - - - - | √ | - - - - | - - - - |
SD Card | - - - - | - - - - | - - - - | 2 GB | - - - - |
Model | DSO5202P | DSO5102P | DSO5072P |
Bandwidth | 200MHz | 100MHz | 70MHz |
Rise Time at BNC( typical) | <1.8ns | <3.5ns | <5ns |
Sample Rate | Real-Time Sample: 1GS/s | ||
Equivalent Sample: 25GS/s | |||
Acquisition Modes | |||
Normal | Normal data only | ||
Peak Detect | High-frequency and randon glith capture | ||
Average | Wavefom Average, selectable 4,8,16,32,64,128 | ||
Inputs | |||
Inputs Coupling | AC, DC, GND | ||
Inpits Impendance | 1MΩ±2% ‖20pF±3pF | ||
Probe Attenuation | 1X, 10X | ||
Supported Probe Attenuation Factor | 1X, 10X, 100X, 1000X | ||
Maximum Input Voltage | CAT I and CAT II: 300VRMS (10×), Installation Category; | ||
CAT III: 150VRMS (1×); | |||
Horizontal | |||
Sample Rate Range | 500MS/s--1GS/s | ||
Waveform Interpolation | (sin x)/x | ||
Record Length | 40K | ||
SEC/DIV Range | 2ns/div to 40s/div | 4ns/div to 40s/div | |
Sample Rate and Delay Time Accuracy | ±50ppm(at over any ≥1ms time interval) | ||
Position Range | 2ns/div to 10ns/div; | 20ns/div to 80us/div; (-8div x s/div) to 40ms; | |
(-4div x s/div) to 20ms; | 200us/div to 40s/div; (-8div x s/div) to 400s | ||
Delta Time Measurement Accuracy | Single-shot, Normal mode:± (1 sample interval +100ppm × reading + 0.6ns); | ||
Vertical | |||
Vertical Resolution | 8-bit resolution, all channel sampled simultaneously | ||
Position Range | 2mV/div to 200mV/div, ±2V | ||
200mV/div to 5V/div, ±50V | |||
Analog Bandwidth in Normal and Average modes at BNC or with probe, DC Coupled | 2mV/div to 20mV/div, ±400mV; | ||
Math | +, -, *, /, FFT | ||
FFT | Windows: Hanning, Flatop, Rectamgular, Bartlett, Blackman; | ||
1024 sample point | |||
Bandwidth Limit | 20MHz | ||
Low Frequency Response (-3db) | ≤10Hz at BNC | ||
DC Gain Accuracy | ±3% for Normal or Average acquisition mode, 5V/div to 10mV/div; | ||
±4% for Normal or Average acquisition mode, 5mV/div to 2mV/div | |||
DC Measurement Accuracy, Average Acquisition Mode | When vertical displacement is zero, and N ≥16:± (3% × reading + 0.1div + 1mV) only 10mV/div or greater is selected; | ||
When vertical displacement is not zero, and N≥16: ± [3% × (reading + vertical position) + 1% of vertical position + 0.2div]; Add 2mV for settings from 2mV/div to 200mV/div; add 50mV for settings from 200mV/div to 5V/div | |||
Volts Measurement Repeatability, Average Acquisition Mode | Delta volts between any two averages of ≥16 waveforms acquired under same setup and ambient conditions | ||
Trigger System | |||
Trigger Types | Edge, Video, Pulse, Slope, Over time, Alternative | ||
Trigger Source | CH1, CH2, EXT, EXT/5, AC Line | ||
Trigger Modes | Auto, Normal, Single | ||
Coupling Type | DC, AC, Noise Reject, HF Reject, LF Reject | ||
Trigger Sensitivity | DC(CH1,CH2):1div from DC to 10MHz; 1.5div from 10MHz to 100MHz; 2div from 100MHz to Full; | ||
DC(EXT): 200mV from DC to 100MHz; 350mV from 100MHz to 200MHz; | |||
DC(EXT/5):1V from DC to 100MHz;1.75V from 100MHz to 200MHz; | |||
AC: Attenuates signals below 10Hz; | |||
HF Reject: Attenuates signals above 80kHz; | |||
LF Reject: Same as the DC-coupled limits for frequencies above 150kHz; attenuates signals below 150kHz | |||
Trigger Level Range | CH1/CH2: ±8 divisions from center of screen; | ||
EXT: ±1.2V; | |||
EXT/5:±6V | |||
Trigger Level Accuracy( typical)Accuracy is for signals having rise and fall times ≥20ns | CH1/CH2: 0.2div × volts/div within ±4 divisions from center of screen; | ||
EXT: ± (6% of setting + 40mV); | |||
EXT/5: ± (6% of setting + 200mV); | |||
Set Level to 50%(typical) | Operates with input signals ≥50Hz | ||
Video Trigger | |||
Video Trigger Type | CH1, CH2: Peak-to-peak amplitude of 2 divisions; | ||
EXT: 400mV; | |||
EXT/5: 2V | |||
Signal Formats and Field Rates, Video Trigger Type | Supports NTSC, PAL and SECAM broadcast systems for any field or any line | ||
Holdoff Range | 100ns ~ 10s | ||
Pulse Width Trigger | |||
Pulse Width Trigger Mode | Trigger when (< , >, = , or ≠); Positive pulse or Negative pulse | ||
Pulse Width Trigger Point | Equal: The oscilloscope triggers when the trailing edge of the pulse crosses the trigger level. | ||
Not Equal: If the pulse is narrower than the specified width, the trigger point is the trailing edge. Otherwise, the oscilloscope triggers when a pulse continues longer than the time specified as the Pulse Width. | |||
Less than: The trigger point is the trailing edge. | |||
Greater than (also called overtime trigger): The oscilloscope triggers when a pulse continues longer than the time specified as the Pulse Width | |||
Pulse Width Range | 20ns ~ 10s | ||
Slope Trigger | |||
Slope Trigger Mode | Trigger when (< , > , = , or ≠ ); Positive slope or Negative slope | ||
Slope Trigger Point | Equal: The oscilloscope triggers when the waveform slope is equal to the set slope. | ||
Not Equal: The oscilloscope triggers when the waveform slope is not equal to the set slope. | |||
Less than: The oscilloscope triggers when the waveform slope is less than the set slope. | |||
Greater than: The oscilloscope triggers when the waveform slope is greater than the set slope. | |||
Time Range | 20ns ~ 10s | ||
Overtime Trigger | |||
Over Time Mode | Rising edge or Falling edge | ||
Time Range | 20ns ~ 10s | ||
Alternative Trigger | |||
Trigger on CH1 | Internal Trigger: Edge, Pulse Width, Video, Slope | ||
Trigger on CH2 | Internal Trigger: Edge, Pulse Width, Video, Slope | ||
Trigger Frequency Counter | |||
Readout Resolution | 6 digits | ||
Accuracy (typical) | ±30ppm (including all frequency reference errors and ±1 count errors) | ||
Frequency Range | AC coupled, from 4Hz minimum to rated bandwidth | ||
Signal Source | Pulse Width or Edge Trigger modes: all available trigger sources | ||
The Frequency Counter measures trigger source at all times, including when the oscilloscope acquisition pauses due to changes in the run status, or acquisition of a single shot event has completed. | |||
Pulse Width Trigger mode: The oscilloscope counts pulses of significant magnitude inside the 1s measurement window that qualify as triggerable events, such as narrow pulses in a PWM pulse train if set to < mode and the width is set to a relatively small time. | |||
Edge Trigger mode: The oscilloscope counts all edges of sufficient magnitude and correct polarity. | |||
Video Trigger mode: The Frequency Counter does not work. | |||
Measure | |||
Cursor Measurement | Voltage difference between cursors: △V | ||
Time difference between cursors: △T | |||
Reciprocal of △T in Hertz (1/ΔT) | |||
Auto Measuerment | Frequency, Period, Mean, Pk-Pk, Cycli RMS, Minimum, Maximum, Rise time, Fall Time, +Pulse Width, -Pulse Width, Delay1-2Rise, Delay1-2Fall, +Duty, -Duty, Vbase, Vtop, Vmid, Vamp, Overshoot, Preshoot, Preiod Mean, Preiod RMS, FOVShoot, RPREShoot, BWIDTH, FRF, FFR, LRR, LRF, LFR, LFF | ||
General Specification | |||
Display Type | 7 inch 64K color TFT (diagonal liquid crystal) | ||
Display Resolution | 800 horizontal by 480 vertical pixels | ||
Display Contrast | Adjustable (16 gears) with the progress bar | ||
Dimension | Length 385mm, Width 200mm, Height 245mm | ||
Weight | 3.5KG(with Packing); 2.08KG(without Packing) |
*From: |
Enter your email |
*Message: |
Enter your Message |
![]() |