100MHz Handheld Scopemeter

Sample Modes

Real-Time Sample

Normal

Normal data only

Peak Detect

High-frequency and randon glith capture

Average

Wavefom Average, selectable 4,8,16,32,64,128

Inputs Coupling

AC, DC, GND

Inputs Impendance

1MΩ±2% ‖20pF±3pF

Probe Attenuation

1X, 10X

Supported Probe Attenuation Factor

1X, 10X, 100X, 1000X

Maximum Input Voltage

CAT I and CAT II: 300VRMS (10×), Installation Category; CAT III: 150VRMS   (1×)

Horizontal System

Sample Rate Range

1GS/s

Waveform Interpolation

(sin x)/x

Record Length

2M

SEC/DIV Range

4ns/div~2000s/div, in a  2, 4, 8 sequence

2ns/div~2000s/div, in a  2, 4, 8 sequence

Sample Rate and Delay Time Accuracy

±50ppm over any ≥1ms time interval

Scanning Speed    Range

4ns/div to 8ns/div; (-8div x s/div) to 40ms;
  20ns/div to 80μs/div;(-8div×s/div) to 40ms
  200μs/div to 40s/div; (-8div×s/div) to 400s

2ns/div to10ns/div;
   (-4div×s/div) to 20ms;

Delta Time Measurement Accuracy 
  (Full Bandwidth)

Single-shot, Normal mode:± (1 sample   interval +100ppm × reading + 0.6ns);
  >16 averages:± (1 sample interval + 100ppm × reading + 0.4ns);Sample   interval = s/div ÷ 200

Vertical System

Vertical Resolution

8-bit resolution, all channel sampled simultaneously

Volts Range

2mV/div to 100V/div at input BNC

Bandwidth

70MHz

100MHz

150MHz

200MHz

Rise Time at BNC( typical)

5ns

3.5ns

2.3ns

1.8ns

Analog Bandwidth in Normal   and 

Average modes at BNC or with p

robe, DC Coupled

±400V(100V/div-20V/div);  ±50V(10V/div-5V/div);   ±40V(2V/div-500mV/div); 
  ±2V(200mV/div-50mV/div); ±400mV(20mV/div-2mV/div)

Math

+, -, *, /, FFT

FFT

Windows:Hanning, Flatop, Rectamgular, Bartlett, Blackman; 1024 sample   point

Bandwidth Limit

20MHz

Low Frequency Response (-3db)

≤10Hz at BNC

Trigger System

Trigger Types

Edge, Video, Pulse, Slope, Over time, Alternative

Trigger Source

CH1, CH2, AC Line

Trigger Modes

Auto, Normal,   Single

Coupling Type

DC, AC, HF Reject, LF Reject, Noise Reject

Trigger Sensitivity

DC(CH1,CH2): AC; HF Reject; LF Reject

Trigger Level Range

CH1/CH2: ±8 divisions from center of screen; 

Video Trigger

Video Trigger Type

CH1, CH2: Peak-to-peak amplitude of 2 divisions;

Signal Formats and Field Rates

Supports NTSC, PAL and SECAM broadcast systems for any field or any line

Holdoff Range

100ns ~ 10s

Pulse Width Trigger

Pulse Width Trigger Mode

Trigger when (< , >, = , or ≠); Positive pulse or Negative pulse

Pulse Width Trigger Point

Equal: The oscilloscope triggers when the trailing edge of the pulse   crosses the trigger level.

Not Equal: If the pulse is narrower than the specified width, the   trigger point is the trailing edge. Otherwise, the oscilloscope triggers when   a pulse continues longer than the time specified as the Pulse Width.

Less than: The trigger point is the trailing edge.

Greater than (also called overtime trigger): The oscilloscope triggers   when a pulse continues longer than the time specified as the Pulse Width

Pulse Width Range

20ns ~ 10s

Slope Trigger

Slope Trigger Mode

Trigger when (< , > , = , or ≠ ); Positive slope or Negative slope

Slope Trigger Point

Equal: The oscilloscope triggers when the waveform slope is equal to the   set slope.

Not Equal: The oscilloscope triggers when the waveform slope is not   equal to the set slope.

Less than: The oscilloscope triggers when the waveform slope is less   than the set slope.

Greater than: The oscilloscope triggers when the waveform slope is   greater than the set slope.

Time Range

20ns ~ 10s

Overtime Trigger

Over Time Modee

Rising edge or Falling edge

Time Range

20ns ~ 10s

Alternative Trigger

Trigger on CH1

Internal Trigger: Edge, Pulse Width, Video, Slope

Trigger on CH2

Internal Trigger: Edge, Pulse Width, Video, Slope

Trigger Frequency Counter

Readout Resolution

6 digits

Accuracy (typical)

±30ppm (including all frequency reference errors and ±1 count errors)

Frequency Range

AC coupled, from 4Hz minimum to rated bandwidth

Signal Source

Pulse Width or Edge Trigger modes: all available trigger sources

The Frequency Counter measures trigger source at all times, including   when the oscilloscope acquisition pauses due to changes in the run status, or   acquisition of a single shot event has completed.

Pulse Width Trigger mode: The oscilloscope counts pulses of significant   magnitude inside the 1s measurement window that qualify as triggerable   events, such as narrow pulses in a PWM pulse train if set to < mode and   the width is set to a relatively small time.

Edge Trigger mode: The oscilloscope counts all edges of sufficient   magnitude and correct polarity.

Video Trigger mode: The Frequency Counter does not work.

Measure

Cursor Measurement

Manual: Voltage difference between cursors: △V

Time difference between cursors: △T

Reciprocal of △T in Hertz (1/ΔT);

Tracing: The valtage and time at a waveform point;

Auto Measuerment

Frequency, Period, Mean, Pk-Pk, Cycli RMS, Minimum, Maximum, Rise time,   Fall Time, +Pulse Width, -Pulse Width, Delay1-2Rise, Delay1-2Fall, +Duty,   -Duty, Vbase, Vtop, Vmid, Vamp, Overshoot, Preshoot, Preiod Mean, Preiod RMS,

Scope Trendplot

1.2M Point

Waveform Generator Mode

Frenquency Range

1Hz(DC)~25MHz

DAC Clock

2K~200MHz adjustable

Memory Depth

4KSa

Vertical Resolution

12 Bits

Stability

<30ppm

Amplitude

±3.5V Max.

Output Impedance

50 Ω

Output Current

50mA Ipeak=50mA

System Bandwidth

25M

Harmonic Wave Distortion

 -50dBc(1KHz),  -40dBc(10KHz)

General Specifications

Display Resolution

640 horizontal by 480 vertical pixels

Display Contrast

Adjustable (16 gears) with the progress bar

Frequency(typical)

1kHz

Dimension

260mm*220mm* 75mm

Weight

2.5KG(without Packing)

Models

SHS806/SHS810/SHS815/SHS820

DSO8072E/DSO8102E/
DSO8152E/DSO8202E

Channels

2

2

Bandwidth

60MHz/100MHz/150MHz/200MHz

70MHz/100MHz/150MHz/200MHz

Real Time Sampling Rate

SHS806/SHS810/SHS815: 
1GSa/s(1CH), 500MSa/s(2CH)
SHS820: 500MSa/s

1GS/s

Equivalent Sampling Rate

50GSa/s

- - - -

Memory Length

2Mpts:SHS806/SHS810/SHS815;
32kpts:SHS820

2Mpts

Vertical Sensitivity

2mV~100V/div

2mV~100V/div

Horizontal Range

5ns~50s/div:SHS806;
2.5ns~50s/div:SHS810/SHS815/SHS820

4ns/div~2000s/div:DSO8072E/DSO8102E;
2ns/div~2000s/div:DSO8152E/DSO8202E

Display

5.7 inch

5.6 inch

Data Recorder

√

√

Signal Generator

- - - -

√

Multimeter

√

√

Maximum Input Voltage

AC: 750V; DC:   1000V

AC: 600V; DC:   800V

Maximum Input   Current

AC: 10A;   DC: 10A

AC: 10A;   DC: 10A